多层圆片级堆叠THz硅微波导结构的制作

基于微电子机械系统(MEMS)工艺,提出一种多层圆片堆叠的THz硅微波导结构及其制作方法。为了验证该结构在制作THz无源器件中的优势,基于6层圆片堆叠的硅微波导结构,设计了一种中心频率365 GHz、带宽80 GHz的功率分配/合成结构,并对其进行了仿真。研究了制作该结构的工艺流程,攻克了工艺过程中的关键技术,包括硅深槽刻蚀技术和多层热压键合技术,并给出了工艺结果。最终实现了多层圆片堆叠功率分配/合成结构的工艺制作和测试。测试结果表明,尽管样品的插入损耗较仿真值增加3 dB左右,考虑到加工误差和夹具损耗等情况,样品主要技术指标与设计值较为一致。     

Design of an adaptive super-twisting decoupled terminal sliding mode control scheme for a class of fourth-order systems

This paper proposes an adaptive super-twisting decoupled terminal sliding mode control technique for a class of fourth-order systems. The adaptive-tuning law eliminates the requirement of the knowledge about the upper bounds of external perturbations. Using the proposed control procedure, the state variables of cart-pole system are converged to decoupled terminal sliding surfaces and their equilibrium points in the finite time. Moreover, via the super-twisting algorithm, the chattering phenomenon is avoided without affecting the control performance. The numerical results demonstrate the high stabilization accuracy and lower performance indices values of the suggested method over the other ones. The simulation results on the cart-pole system as well as experimental validations demonstrate that the proposed control technique exhibits a reasonable performance in comparison with the other methods.     

New batch and continuous systems for converting hydrogen from water hyacinth

Water hyacinth was the chosen alternative biomass for H₂ production in this study. A batch and a continuous pilot plant systems are proposed. A batch system of 500?ml capacity was developed first for finding an appropriate biomass ratio which was found to be 2.5%wt. Results from the batch system was used to construct a kinetic model of water hyacinth hydrolysis. The same biomass and water ratio was used in the continuous system. Besides water hyacinth, glucose and cellulose?+?lignin biomasses were tested. During processing, temperature, pressure, and electric consumption of the system were recorded. The quality and quantity of gas products were analyzed by gas chromatography (GC). The water hyacinth biomass attained the highest rate of H₂ production (providing energy of 11.43?kWh/mole of glucose). Comparing the batch and continuous pilot systems, the continuous system achieved 2.7 times more H₂ mole% than the batch system did.     

浅谈高压中速磨粉系统在磷酸二铵生产中的应用

通过对磷酸二铵生产造粒特性分析,高压中速磨粉机原理分析,结合实践生产中的工艺需求,利用高压中速磨粉系统将颗粒状不合格品磨成细粉后添加进系统重新喷浆造粒,提高返料添加量,减少不合格品的产生,腾空仓库有限货位,以获取更大的经济价值。     

Common Mode Voltage Reduction Using 3D-SVPWM for 3-level CI-NPC Inverter with Hybrid Energy System

This paper elucidates Common Mode Voltage (CMV) reduction in transformerless 3-phase 3-level Coupled Inductor Neutral Point (CI-NPC) Clamped Inverter with Hybrid Energy System. The three dimensional Space Vector Pulse Width Modulation (3D-SVPWM) with Nearest State Vector (NSV) is implemented to reduce the CMV by proper selection of medium, large and small vectors in 3D cubic space region. This NSV scheme in addition to CMV reduction, reduces the capacitor voltage balancing issues and minimizes switching losses. The proposed control provides full utilization of dc link voltage with reduced harmonics. This 3-level CI-NPC inverter is energized by hybrid energy source which includes photovoltaic system and wind energy system. The results obtained for the proposed scheme through simulation and experimental setup is compared with the conventional 2D-SVPWM and 3D-SVPWM scheme. From the compared results it is evident that the proposed scheme reduces CMV to a larger extent than 2D and 3D-SVPWM control. The simulation and experimental results are verified using matlab-simulink and FPGA-Spartan-6 controller respectively.     

Focusing characteristics of the relativistic electron beam transmitting in ion channel

Based on the beam–plasma system model established in this paper, the trajectory of the electron beam in the ion channel is studied quantitatively through the envelope equation. Under different initial system parameters, the focusing transmission conditions of the beam in the ion channel are discussed. Then, a series of particle-in-cell simulations are performed, which generally versifies the theoretical results and shows some further details of the focusing behavior of the beam. It is found that the deceleration of some electrons around the focusing point or the beam–plasma interaction at the ion channel boundary will result in the generation of the residual electrons,which forms the electron return current that leads to the new instabilities influencing the focusing characteristics of the beam.     

Stochastic analysis of strongly non-linear elastic impact system with Coulomb friction excited by white noise

The stochastic response of frictionally damped strongly non-linear elastic impact oscillator subjected to white noise excitation and its stochastic bifurcation are considered. By the stochastic averaging method based on generalized harmonic function, one can obtain the stationary probability density function of this system. The effects of system parameters on the responses are investigated and the analytical results were verified by comparing with numerical results from Monte Carlo simulations. Stochastic bifurcations are discussed through a qualitative change of the stationary probability distribution, which indicates that the coefficient of friction, damping constant of the elastic impact force respectively, can be treated as bifurcation parameters.     

门架式堆取料机在铜冶炼中的生产实践

针对铜冶炼工艺的特点,从门架式堆取料机对前后工序衔接、结构、原理出发,介绍了其在熔炼炉系统和吹炼炉系统中的应用情况。经过试生产期的生产实践证明,门架式堆取料机具有场地利用率高、取料量大,自动化程度高和安全环保等优点。     

[成形过程仿真优化与集成计算材料工程]限定加热管布局的快速热循环注塑成形模具电加热系统优化

针对管道布局、最大允许能耗给定条件下快速热循环注塑成形（RHCM）注塑模具型腔表面快速均匀加热的问题，提出以单根加热棒热流密度为设计变量，以模具型腔表面升温效率和温度分布均匀性为目标，结合有限元模拟、响应面设计以及多目标粒子群优化技术来优化RHCM模具电加热系统。与优化前相比，加热系统优化后，模具型腔表面最大温差降低63.4%，加热系统总能耗降低9%。对比了不同注塑成形工艺条件下成形的平板塑件表面质量，结果表明，相对传统注塑成形（CIM）工艺，RHCM工艺将制品表面粗糙度Ra从320 nm降低到118 nm，并有效抑制了制品表面熔接痕、缩痕等缺陷；发现制品表面粗糙度与型腔表面对应点温度成负相关，说明优化后的型腔表面温度分布更有利于提升制品表面质量。